Flushing a tankless: why it matters, how often, and DIY vs calling a pro
A tankless water heater has no tank to corrode — but it has a heat exchanger that scale quietly chokes, and flushing (descaling) is the single maintenance task that decides whether yours lasts 20 years or 8. Hard-water minerals bake onto the exchanger's narrow passages every time it fires; left alone they restrict flow, drop your hot-water output, spike your gas or electric bill, and eventually throw the error codes most people mistake for a dying unit. The good news: a flush is cheap and, for most homeowners, DIY-able in under an hour. The honest framing below is how often to do it, what a DIY flush actually involves, and when it's worth paying a pro.
How often to flush — and why your water decides, not the calendar
The default advice is once a year, and that's a fine rule for average water. But the real driver is your water hardness: on very hard water (10+ grains/gal) an untreated tankless can need descaling every 6 months, while a home on softened or naturally soft water can stretch to every 18–24 months. Signs you're overdue regardless of the calendar: fluctuating hot-water temperature, reduced flow at the tap, a longer wait for hot water, or a scale/maintenance error code (Rinnai LC codes, Navien E-codes). If you have a water softener upstream, you've already bought yourself the longest interval — scale is a hard-water problem first and foremost.
What a DIY flush actually involves (and the one part most people skip)
A DIY descale is genuinely simple if your unit has isolation/service valves installed (the two tee-handle valves at the cold and hot connections — if you don't have them, that's the first thing to add, ~$50 in parts). The kit is a submersible pump, two hoses, a bucket, and about 3–4 gallons of white vinegar (or a food-safe descaling solution). You close the isolation valves to the house, connect the pump to circulate the vinegar through the heat exchanger for 45–60 minutes, then flush clean water through and clear the inlet screen filter. A ready-made flush kit runs $40–130; vinegar is a few dollars. The part people skip: cleaning the small inlet water filter/screen at the same time — a clogged screen mimics scale and throws the same low-flow codes.
DIY vs calling a plumber: the honest cost math
A professional descaling service runs $100–200, and it's money well spent in three cases: you don't have isolation valves (a plumber can add them and flush in one visit), your unit is throwing codes you can't clear, or you simply don't want to handle the pump-and-vinegar routine. But for a valve-equipped unit, the DIY cost is basically the vinegar — the flush kit pays for itself on the first use. Either way, descaling is cheaper than every alternative: a neglected exchanger that scales shut is a $500–1,000+ repair, and many manufacturers will void the heat-exchanger warranty if you can't show the unit was flushed on schedule. An hour a year — or $150 — protects the single most expensive part in the machine.
When flushing is no longer worth it (and the swap makes sense)
Descaling restores a unit that's scaled; it can't fix one that's worn out. If your tankless is past ~12–15 years, out of warranty, and still throwing exchanger or ignition faults after a proper flush, you're maintaining a unit near end-of-life — and modern condensing models are meaningfully more efficient (0.93–0.98 UEF vs the ~0.82 of older non-condensing units), so the replacement often pays part of its own way in gas savings. The ranking below is pre-weighted toward buy-and-forget reliability so, if you're at the replace point, the lowest-maintenance best-value unit floats to the top; every slider is yours to override.
What about installation cost?
Sticker price is only half the story — condensing units need special venting, electric units may need a panel upgrade. The tool ranks on unit value; use the fuel filter to compare within an install type (all-gas vs all-electric) so you're not comparing a cheap electric against a gas unit that costs $1,500 to vent. (A dedicated installation-cost calculator — the highest-demand tankless search — is live.)
Condensing vs non-condensing: the choice that drives both your bill and your install
This is the first real fork. A non-condensing unit (e.g. the Rinnai V75iN, ~0.81 UEF) is cheaper up front (~$780) but vents hot exhaust through expensive stainless-steel or Category III venting and wastes more heat. A condensing unit (Navien NPE, Rinnai RX, Rheem Prestige — 0.93–0.98 UEF) captures a second pass of heat from the exhaust, running cool enough to vent through cheap PVC and cutting gas use meaningfully. Rule of thumb: condensing costs $300–600 more for the unit but is usually cheaper to vent and pays back the difference in gas savings within a few years — especially if you run a lot of hot water. The tool's UEF axis is where this shows up; sort by it to see the efficiency spread directly.
Gas vs electric tankless: which one fits your house
The honest limiter on electric tankless isn't efficiency — electric units hit ~0.99 UEF — it's flow in cold climates and your electrical panel. The best electric units here (Stiebel Eltron Tempra 29, Rheem RTEX-27) top out around 2.9–3.1 GPM at a 70° rise and can demand 100+ amps of dedicated service, often forcing a panel upgrade. That's fine for a warm climate, a point-of-use application, or a small household — and electric wins on up-front price ($430–850) and needs no venting at all. Gas (natural gas or propane) is what a cold-climate whole-house family wants: 4.5–5.7 GPM at rise, no panel upgrade, but it needs a gas line and venting. Use the fuel filter above to compare like-for-like instead of pricing a $430 electric against a $1,500 gas unit that solves a different problem.
Why we don't just name a winner
"Best tankless" depends entirely on your fuel, climate and household size. A cold-climate family cares about flow; a bill-watcher cares about UEF; a landlord cares about warranty. One name buries that — the Value Score keeps it in your hands, formula in the open right above. (Sizing for a specific household? See our tankless sizing for a family of 4 walkthrough.)
The specs, briefly
UEF = efficiency, how much energy reaches the water (higher = lower bills). Flow @ 70° rise = real cold-weather simultaneous-shower capacity. HX warranty = years on the heat exchanger, the part that fails. Recirculation = instant hot water at the tap (built-in pump only — "recirc-capable" without a factory pump doesn't count here). Min-flow = how little flow fires it (low = no cold-water sandwich).
Specs verified Aug 2026 against manufacturer spec sheets + ENERGY STAR product finder. Prices are approximate street prices (unit only, not installed) pending live-retailer verification. Some links may be affiliate; that never changes the Value Score — the math runs on published specs, not payouts.